- 您现在的位置：买卖IC网 > Sheet目录400 > CC2480A1RTC (Texas Instruments)IC Z-ACCEL ZIGBEE PROC 48-VQFN
CC2480
10.12 PCB Layout Recommendation
In the Texas Instruments reference design, the
top layer is used for signal routing, and the
The external components should be as small
as possible (0402 is recommended) and
open areas
are filled
with metallization
surface mount devices must be used.
connected to ground using several vias. The
area under the chip is used for grounding and
must be well connected to the ground plane
with several vias.
The ground pins should be connected to
ground as close as possible to the package
pin using individual vias. The de-coupling
capacitors should also be placed as close as
possible to the supply pins and connected to
the ground plane by separate vias. Supply
power filtering is very important.
10.13 Antenna Considerations
If using any external high-speed digital
devices, caution should be used when placing
these in order to avoid interference with the
RF circuitry.
It is strongly advised that this reference layout
is followed very closely in order to obtain the
best performance.
The schematic, BOM and layout Gerber files
for the reference designs are all available from
the TI website.
CC2480 can be used together with various
types of antennas. A differential antenna like a
the antenna. Many vendors offer
antennas intended for PCB mounting.
such
dipole would be the easiest to interface not
needing a balun (balanced to un-balanced
transformation network).
The length of the λ /2-dipole antenna is given
by:
L = 14250 / f
where f is in MHz, giving the length in cm. An
antenna for 2450 MHz should be 5.8 cm. Each
arm is therefore 2.9 cm.
Other commonly used antennas for short-
range communication are monopole, helical
and loop antennas. The single-ended
monopole and helical would require a balun
network between the differential output and
the antenna.
Monopole antennas are resonant antennas
with a length corresponding to one quarter of
the electrical wavelength ( λ /4). They are very
easy to design and can be implemented
simply as a “piece of wire” or even integrated
into the PCB.
The length of the λ /4-monopole antenna is
given by:
L = 7125 / f
where f is in MHz, giving the length in cm. An
antenna for 2450 MHz should be 2.9 cm.
Non-resonant monopole antennas shorter than
λ /4 can also be used, but at the expense of
range. In size and cost critical applications
such an antenna may very well be integrated
into the PCB.
Enclosing the antenna in high dielectric
constant material reduces the overall size of
Helical antennas can be thought of as a
combination of a monopole and a loop
antenna. They are a good compromise in size
critical applications. Helical antennas tend to
be more difficult to optimize than the simple
monopole.
Loop antennas are easy to integrate into the
PCB, but are less effective due to difficult
impedance matching because of their very low
radiation resistance.
For low power applications the differential
antenna is recommended giving the best
range and because of its simplicity.
The antenna should be connected as close as
possible to the IC. If the antenna is located
away from the RF pins the antenna should be
matched to the feeding transmission line
(50 ? ).
CC2480 Data Sheet SWRS074
Page 35 of 43
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
CDJB3
JUNCTION BOX COLORDRV 1/IN 3/OUT
CEA-06-062UR-350
STRAIN GAGE 350 OHM RECT
CEA-06-062UT-350
STRAIN GAGE 350 OHM TEE
CEA-06-062UW-350
STRAIN GAGE 350 OHM LINEAR
CEA-06-062WT-350
STRAIN GAGE 350 OHM TEE
CEA-06-125UN-350
STRAIN GAGE 350 OHM LINEAR
CEA-06-125UR-350
STRAIN GAGE 350 OHM RECT
CEA-06-125UT-350
STRAIN GAGE 350 OHM TEE
相关代理商/技术参数
CC2480A1RTCR
功能描述:射频微控制器 - MCU Z-Accel 2.4 GHz Zig Bee Processor
RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:Si100x 数据总线宽度:8 bit 最大时钟频率:24 MHz 程序存储器大小:64 KB 数据 RAM 大小:4 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LGA-42 安装风格:SMD/SMT 封装:Tube
CC2498-000
功能描述:集管和线壳 MTCPQKT1R2SFDD RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector
CC24BODKCV3SRD302Q250M
制造商:Ferraz Shawmut 功能描述:
CC24BODKCV3SRE300Q100M
制造商:Ferraz Shawmut 功能描述:
CC24BODKCV3SRE300Q20M
制造商:Ferraz Shawmut 功能描述:
CC24BODKCV3SRE300Q63M
制造商:Ferraz Shawmut 功能描述:
CC24BODKCV3SRF302Q400M
制造商:Ferraz Shawmut 功能描述:
CC-24K2-CP
功能描述:MODEM 2400BAUD PARALLEL 3.3V RoHS:否 类别:集成电路 (IC) >> 接口 - 调制解调器 - IC 和模块 系列:- 标准包装:25 系列:- 数据格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 电源电压:3.3V 安装类型:- 封装/外壳:- 供应商设备封装:- 包装:托盘 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名称:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574